Knowing how old your water heater is can save you from an unexpected cold shower or a flooded utility closet.

Customer Issue

A homeowner in Berea had an aging water heater that was struggling to perform and lacked thermal expansion protection to meet modern building codes.

What We Did

Our team installed a new 30-gallon electric water heater, adding a top-mounted thermal expansion tank and press fittings.

Result

A clean, code-compliant installation delivering consistent hot water with built-in protection against pressure spikes.

Why It Matters

Most tank water heaters have a lifespan of 8 to 12 years. You can check your own unit’s age on the manufacturer sticker—the first two digits of the serial number typically show the year it was built (for example, “25” indicates 2025). Adding a thermal expansion tank (typically a $150–$250 upgrade) gives expanding hot water a safe place to go. This simple addition cushions your plumbing from thermal pressure, helping your water heater last significantly longer.

Here to Help

Shoutout to Trenton and Wyatt for another solid installation! If your water heater’s serial number starts with 15 or lower (or it is in the 90’s)—or if it’s been years since your last system maintenance—give Right There Plumbing a call. We serve all of Central Kentucky with honest inspections, flushes, and replacements. Check out our Water Heater Services or reach out today!

Before drywall goes up or concrete gets poured, every drain line needs to prove it’s leak-free under real-world pressure.

Customer Issue

On a new build in Loretto, confirming the underground and in-wall piping was 100% airtight was essential before closing in the framing and slab.

What We Did

David and Everett executed a complete pressure test. They inserted inflatable test plugs into the standpipe and slab drains, pressurized the system using an inflator, and hooked up a test gauge to monitor for any pressure drop across the entire system.

Result

A fully verified, leak-free drainage system ready for concrete and drywall.

Why It Matters

Drains mostly rely on gravity, but high-volume water discharges—like a modern washing machine pump—create real surge pressure inside the drain pipes. Super small gaps in glue joints can leak water or can let toxic sewer gases back into living spaces. Pressurizing the system with a gauge proves that every joint is sealed tight before it’s hidden forever behind drywall or under concrete.

Here to Help

Great work by David and Everett on another solid plumbing job and testing process. For custom builds or remodels in Loretto (40037) or anywhere in Central Kentucky, Right There Plumbing delivers code-conscious quality you can count on. Check out our Services or contact us today!

Building a new home means putting complete trust in the work that eventually gets hidden behind drywall.

Customer Issue

On this custom build in Crab Orchard, the layout called for a clean, code-conscious plumbing rough-in across the bathrooms and laundry room to ensure fast drainage and complete sewer gas protection.

What We Did

Trenton and Wyatt handled the rough-in phase for this home. They installed the complete drain, waste, and vent (DWV) system and run PEX water lines. In the laundry room, they mounted the outlet box, set up the P-trap, and routed vertical vents through the wall studs.

Result

A quiet, code-compliant DWV system that drains smoothly, passes inspection, and leaves the home ready for drywall.

Why It Matters

Every fixture relies on two key components: a P-trap and a vent pipe. The P-trap holds a standing water seal that stops foul, dangerous sewer gas from backing into your living space. The vent pipe supplies air pressure so waste moves freely—much like holding the air cap open on a water jug so it pours smoothly. Without proper venting, gravity pulls water right out of the P-trap, breaking that seal.

During the job, we noticed a handwritten note on the stud framing. Even with the quality wood and workmanship of this place, it was a good reminder of what really holds up things in life’s uncertainties and gives peace behind those walls.

Here to Help

Kudos to Trenton and Wyatt for another clean installation. Whether you’re breaking ground in Crab Orchard (40419) or anywhere in Central Kentucky, Right There Plumbing builds systems made to last. Explore our Services or get in touch today.

When framing out a new custom build, it’s easy to focus on room sizes and open layouts. But behind the studs, the geometry of your drain lines determines whether your plumbing works effortlessly or becomes a constant headache.

Customer Issue

During a new residential build in Springfield, our team was tasked with running a long main drain across an unfinished basement ceiling. The challenge on a long run like this isn’t just hanging pipe—it’s maintaining the precise mathematical slope needed to move waste without stealing valuable head clearance for a future finished basement.

What We Did

David, Trenton, and Tanner took on this rough-in project, installing the complete drain, waste, and vent (DWV) system. They carefully set the slope for the main overhead line, secured all branch arms for the laundry and baths, and routed vent stacks up through the wall framing.

Result

A clean, fully code-compliant DWV rough-in that drains reliably and sits tight to the floor joists to maximize basement headroom.

Why It Matters

Why is drain pitch so critical? Gravity plumbing relies on a delicate balance of speed and water volume.

–Too Little Pitch: If a pipe is too flat, water slows down, solids settle at the bottom, and over time you get stubborn grease and debris clogs.

–Too Much Pitch: If a pipe drops too steeply, liquids rush ahead, leaving solid waste behind to dry out on the pipe walls—causing the exact same clogging issue.

Standard code requires a precise 1/4-inch drop per linear foot for pipes under 3 inches. Hitting that exact standard over a 40-plus foot span takes experienced hands and careful planning before drywall goes up.

Here to Help

Great work by David, Trenton, and Tanner on keeping this system tight, sloped, and built to code. Whether you’re breaking ground on a new home or planning a renovation in Springfield (40069) or anywhere in Central Kentucky, Right There Plumbing gets the fundamentals right the first time. Check out our Plumbing Services or reach out to discuss your project.

A custom home build in Crab Orchard living up to its blueprint requires a properly designed plumbing system underneath the floor before any drywall or finished flooring goes in.

Customer Issue On a new residential build, much of the groundwork happens in low-clearance crawlspaces. Setting a consistent, code-compliant pitch across long pipe runs on a muddy site takes careful layout so you don’t compromise floor joists or sacrifice flow.

What We Did Right There Plumbing handled the drain, waste, and vent (DWV) rough-in on this site. Working through tight crawlspace quarters, we ran the pipes and secured every line to the joists using heavy-duty galvanized strapping, ensuring consistent pitch from the farthest fixture to the main line exit.

Result

A clean, durable DWV system installed to code that will drain smoothly for decades.

Why It Matters

In a crawlspace, proper pipe slope and tight hanger spacing aren’t optional. If a long run sags even a quarter inch, waste sits, solids build up, and you end up with recurring clogs down the line. Getting the math and hanging hardware right during the rough-in phase prevents expensive tear-outs later.

Here to Help

Solid work by Trenton and Wyatt on a tough crawlspace setup. If you’re building or renovating in Crab Orchard (40419) or anywhere in Central Kentucky, Right There Plumbing delivers clean, code-compliant work from the ground up. Take a look at our Plumbing Services or contact us to discuss your build.

Building a new home means getting the hidden systems right before drywall covers them up. On a build in Springfield, we focused on executing a clean rough-in according to the home’s architectural plans.  Will mention a few extra details about the laundry room.

Customer Issue The builder needed an inspection-ready rough-in following the project drawings, requiring precise drain venting, clean PEX routing, and full code compliance across the entire floor plan.

What We Did We installed the DWV (drain, waste, vent) system, placing a laundry outlet box with dedicated 2-inch drainage and proper stack venting. We routed PEX supply lines, installed steel nail plates over framing cutouts, set a left-hand tub unit, and installed Delta shower valves before tying in the main water line.

Result The plumbing is completely protected, will flow quietly, and is built to handle heavy appliance discharge without back-pressure.

Why It Matters Modern washing machines pump out water at high volume and speed. Following code-specified drain sizing and stack venting prevents negative pressure—keeping sewer gas out and preventing sudden overflows. Protecting lines with stud plates also prevents accidental drywall screw punctures that cause hidden wall leaks later.

Here to Help Big credit to Robbie, David, and Tanner for executing a clean layout! Whether you’re a contractor or a homeowner building in Springfield (40069) or anywhere in Central Kentucky, Right There Plumbing delivers work you can trust. Explore our new construction plumbing services or reach out today to talk about your next project!